Error running HydroDyn file

Discuss field testing of turbines and structural testing of components.

Moderator: Bonnie.Jonkman

Sai.Chaitanya
Posts: 12
Joined: Sun Nov 25, 2018 9:44 am
Organization: National Institute of Technology Karnataka
Location: India

Error running HydroDyn file

Postby Sai.Chaitanya » Thu Dec 06, 2018 5:40 am

Dear Dr. Jason,

I am doing project on STC platform.
I am getting problem while running the simulation and I couldn't figure out the exact reason for the error. Please guide me to solve this.
The error is as follows:
Running FAST (v8.15.00a-bjj, 12-Apr-2016), compiled as a 32-bit application using single
precision
linked with NWTC Subroutine Library (v2.08.00, 5-Apr-2016)

Heading of the FAST input file:
FAST Certification Test #24: NREL 5.0 MW Baseline Wind Turbine with OC3 Hywind Configuration,
for use in offshore analysis

Running ElastoDyn (v1.03.02a-bjj, 8-Apr-2016).

Running AeroDyn (v15.02.03, 12-Apr-2016).

Running AirfoilInfo (v1.01.00a-bjj, 5-Apr-2016).

Running BEM (v1.01.00a, 12-Apr-2016).

Running InflowWind (v3.02.00a-bjj, 11-Apr-2016).
Opening InflowWind input file: .\5MW_Baseline/NRELOffshrBsline5MW_InflowWind.dat

Reading a 10x10 grid (160 m wide, 10 m to 170 m above ground) with a characteristic wind speed
of 8 m/s. This full-field file was generated by TurbSim (v1.50, 25-Sep-2009) on 06-Dec-2018 at
16:55:23.

Processed 289600 time steps of 80-Hz full-field data (3620 seconds).

Running ServoDyn (v1.05.00a-bjj, 11-Mar-2016).

Running ServoDyn Interface for Bladed Controllers (using Intel Visual Fortran for Windows,
14-Oct-2015).

Running HydroDyn (v2.05.00, 15-Mar-2016).
Generating incident wave kinematics and current time history.
forrtl: severe (59): list-directed I/O syntax error, unit -5, file Internal List-Directed Read
Image PC Routine Line Source
FAST_Win32.exe 012B66BB Unknown Unknown Unknown
FAST_Win32.exe 012B5140 Unknown Unknown Unknown
FAST_Win32.exe 024AF672 Unknown Unknown Unknown
FAST_Win32.exe 02496C92 Unknown Unknown Unknown
FAST_Win32.exe 0244B92B Unknown Unknown Unknown
FAST_Win32.exe 0174F785 _MAIN__ 79 FAST_Prog.f90
FAST_Win32.exe 01530642 Unknown Unknown Unknown
FAST_Win32.exe 025F376F Unknown Unknown Unknown
KERNEL32.DLL 73D48484 Unknown Unknown Unknown
ntdll.dll 7743302C Unknown Unknown Unknown
ntdll.dll 77432FFA Unknown Unknown Unknown

Thank you

Best regards,
Sai Chaitanya

Jason.Jonkman
Posts: 4223
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Error running HydroDyn file

Postby Jason.Jonkman » Thu Dec 06, 2018 7:10 am

Dear Sai,

I'm not sure. Can you attach your HydroDyn input file?

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Sai.Chaitanya
Posts: 12
Joined: Sun Nov 25, 2018 9:44 am
Organization: National Institute of Technology Karnataka
Location: India

Re: Error running HydroDyn file

Postby Sai.Chaitanya » Thu Dec 06, 2018 11:56 am

Dear Dr. Jason,
I am herewith attaching the hydrodyn file.

Thank you

Best regards
Attachments
Hydrodyn.docx
(17.85 KiB) Downloaded 107 times

Jason.Jonkman
Posts: 4223
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Error running HydroDyn file

Postby Jason.Jonkman » Thu Dec 06, 2018 7:44 pm

Dear Sai,

I don't see any obvious problem from my quick review of your HydroDyn input file (but it is difficult to review in MS Word format). A similar question was asked and answered in the following forum topic: viewtopic.php?f=4&t=1206&p=5199. Perhaps the same solution applies to your case?

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Chenxu.Zhao
Posts: 4
Joined: Mon May 20, 2019 4:36 am
Organization: Chongqing University
Location: China

Re: Error running HydroDyn file

Postby Chenxu.Zhao » Mon May 27, 2019 8:59 am

Dear Dr.Jason
I also had problems running the Standalone Hydrodyn , and I haven't found the cause yet.I hope you can help me with this problem.
This Hydrodyn file is NRELOffshrBsline5MW_OC4Jacket_HydroDyn.dat
Error is as follows:

Running HydroDyn (v2.05.00, 15-Mar-2016).
Generating incident wave kinematics and current time history.

Error status and messages after execution:
ErrStat: 4
ErrMsg returned: HydroDyn_Init:Waves_Init:VariousWaves_Init:Cannot allocate array
InitOut%WaveVel.
VariousWaves_Init:Cannot allocate array InitOut%WaveAcc.
VariousWaves_Init:Cannot allocate array InitOut%PWaveVel0.
VariousWaves_Init:Cannot allocate array InitOut%PWaveAcc0.

Thank you
Best regards

Jason.Jonkman
Posts: 4223
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Error running HydroDyn file

Postby Jason.Jonkman » Tue May 28, 2019 6:29 am

Dear Chenxu Zhao,

Did you modify the HydroDyn file NRELOffshrBsline5MW_OC4Jacket_HydroDyn.dat in some way e.g. by increasing the number of hydrodynamic analysis nodes in the strip-theory solution or by modifying the wave definition in some way?

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Chenxu.Zhao
Posts: 4
Joined: Mon May 20, 2019 4:36 am
Organization: Chongqing University
Location: China

Re: Error running HydroDyn file

Postby Chenxu.Zhao » Tue May 28, 2019 8:13 am

Dear Dr.Jason
Thank you very much for your reply
I used the HydroDyn file in test21 that comes with FAST V8 without modifying any data.
And I just added a driver file when running the Standalone hydrodyn(v2.05.00)

Best regards,

Jason.Jonkman
Posts: 4223
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Error running HydroDyn file

Postby Jason.Jonkman » Tue May 28, 2019 9:44 am

Dear Chenxu Zhao,

The error implies that you do not have enough memory to allocate more data. Did you recompile the standalone HydroDyn driver yourself? Have you tried to use the standalone HydroDyn driver for 64-bit Windows provided in the HydroDyn archive (HydroDynDriver_x64.exe)?

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Chenxu.Zhao
Posts: 4
Joined: Mon May 20, 2019 4:36 am
Organization: Chongqing University
Location: China

Re: Error running HydroDyn file

Postby Chenxu.Zhao » Wed May 29, 2019 8:55 pm

Dear Dr.Jason

Thank you very much for your reply. The problem was solved after I used HydroDynDriver_x64.exe.

Best regards,


Return to “Testing”

Who is online

Users browsing this forum: No registered users and 1 guest