Installation of OpenFAST

Provide feedback, request enhancements, and get help with wind energy systems engineering tools.

Moderators: Bonnie.Jonkman, Evan.Gaertner, Pietro.Bortolotti, George.Scott, Katherine.Dykes, Garrett.Barter, Andrew.Ning

Shankar.Sarpate
Posts: 14
Joined: Tue Jul 20, 2010 3:08 pm
Organization: RSE Pune
Location: India
Location: Pune, India
Contact:

Installation of OpenFAST

Postby Shankar.Sarpate » Thu Nov 01, 2018 8:37 pm

Dear All,
I was trying to install OpenFAST as per the attached procedure. There is an error while setup downloading (error message attached).

Please suggest me any other site for downloading the software other than http://www.gtlib.gatech.edu

Thank a lot!
Attachments
OpenFast_Procedure.JPG
OpenFast_Procedure.JPG (105.39 KiB) Viewed 3943 times
Error_message.JPG
Error_message.JPG (34.05 KiB) Viewed 3943 times
Thanks & regards,
Shankar K. Sarpate,
Director,
E-Mobility & Renewable Energy Solutions, Pune,India
Mobile :+91 7758847732
Tel :+91 2114232191
Email: sksarpate@gmail.com

Jason.Jonkman
Posts: 4221
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Installation of OpenFAST

Postby Jason.Jonkman » Fri Nov 02, 2018 9:00 am

Dear Shankar,

I'm only really familiar with Building OpenFAST on Windows with Visual Studio, which is the procedure I'd recommend if you are using Windows.

For specific questions on using Cygwin to install and build OpenFAST, I suggest posting your question on the OpenFAST issues page, where the OpenFAST development community can support you: https://github.com/OpenFAST/openfast/issues. Not everyone in the OpenFAST development community checks this forum regularly.

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Shankar.Sarpate
Posts: 14
Joined: Tue Jul 20, 2010 3:08 pm
Organization: RSE Pune
Location: India
Location: Pune, India
Contact:

Re: Installation of OpenFAST

Postby Shankar.Sarpate » Tue Nov 06, 2018 5:41 am

Dear Jason,
Thank you very much for the guidance!

Now I am working on loads calculations project with IEC 61400-1 Ed3.
In the sample projects, we have limited number of wind conditions simulated. Is it possible to through light on the following points:
1. How we can consider all load cases / simulations running in batch files?
2. Can we assign more than one wind files for one simulations keeping other parameters same?
3. How to generate *.wnd file?

I am going through the FAST manual. And trying to get answer to the above question. Meantime can you provide above information if possible?

Thanks in advance!

Regards,
Shankar Sarpate
Thanks & regards,
Shankar K. Sarpate,
Director,
E-Mobility & Renewable Energy Solutions, Pune,India
Mobile :+91 7758847732
Tel :+91 2114232191
Email: sksarpate@gmail.com

Jason.Jonkman
Posts: 4221
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: Installation of OpenFAST

Postby Jason.Jonkman » Thu Nov 08, 2018 9:25 pm

Dear Shankar,

Normally users develop scripts to run multiple FAST simulations e.g. to simulate multiple wind conditions for the same wind turbine. This has been discussed several times on this forum e.g. viewtopic.php?f=4&t=1938&p=10093 and viewtopic.php?f=4&t=603.

By a *.wnd file, presumably you mean the turbulent wind data file in binary format. (The turbulent wind binary file in Bladed format typically has the *.wnd extension.) However, unless you plan to use Bladed, I would recommend using the TurbSim binary format *.bts. Regardless, both types of turbulent wind data files can be generated using TurbSim: https://nwtc.nrel.gov/turbsim.

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov


Return to “Systems Engineering Software Tools”

Who is online

Users browsing this forum: No registered users and 0 guests