FAST v8.12 and S-Function with "RotCp" in OutList

Provide feedback, request enhancements, and get help with wind-turbine computer-aided engineering tools.

Moderators: Bonnie.Jonkman, Jason.Jonkman

Adrian.Gambier
Posts: 9
Joined: Wed Dec 09, 2015 8:50 am
Organization: Fraunhofer IWES
Location: Germany

FAST v8.12 and S-Function with "RotCp" in OutList

Postby Adrian.Gambier » Thu Dec 10, 2015 6:57 am

Hi,

I am using FAST v8.12 and the given S-Function. However, I added
several additional output parameters in the OutList. I am
now receiving the error "XX is not an available output channel" for
all parameters (like "RotCp", "RotCq", "RotCq", "NacYawErr",
"WindVxi", "TipSpdRat"), which are labeled as "unavailable if
CompAero is False". However, CompAero is not False but 1 or to 2.

Does someone know what I am doing wrong?

Many thanks for the help and
Best regards

Bonnie.Jonkman
Posts: 566
Joined: Thu Nov 10, 2005 10:51 am
Organization: Envision Energy USA
Location: Colorado
Location: Boulder, CO
Contact:

Re: FAST v8.12 and S-Function with "RotCp" in OutList

Postby Bonnie.Jonkman » Thu Dec 10, 2015 10:23 am

Hi, Adrian.

"RotCp", "RotCq", "RotCq", "NacYawErr", and "TipSpdRat" were outputs of FAST v7, but they are not available in FAST v8.

"WindVxi" has been replaced with "Wind1VelX" in the InflowWind input file; this assumes that you have requested at least one wind output location (NWindVel>=1) and it is located at the hub (WindVxiList(1)=0, WindVyiList(1)=0, and WindVziList(1)=<whatever your hub height is>).

When I converted some FAST v7 Simulink models to use FAST v8, I used these equations to get some equivalent FAST v7 variables:

Code: Select all

HorWindV = sqrt( Wind1VelX^2 + Wind1VelY^2 ) 
HorWindDir =  180°/pi * atan2(Wind1VelY,Wind1VelX)
VerWindDir =  180°/pi * atan2(Wind1VelZ,HorWindV)
NacYawErr = HorWindDir-YawPzn-YawBrRDzt- PtfmRDzi
Bonnie Jonkman

Envision Energy USA, 2016-
National Renewable Energy Laboratory, 2003-2016

Jason.Jonkman
Posts: 4962
Joined: Thu Nov 03, 2005 4:38 pm
Location: Boulder, CO
Contact:

Re: FAST v8.12 and S-Function with "RotCp" in OutList

Postby Jason.Jonkman » Thu Dec 10, 2015 2:51 pm

Dear Adrian,

To add to what Bonnie said, with the release of AeroDyn v15 within FAST v8.12, many of these outputs are now available in a bit different form e.g. AeroDyn v15 outputs RtAeroCp, RtAeroCq, RtAeroCt, RtSkew, and RtTSR. See Appendix E of the draft AeroDyn v15 User's Guide and Theory Manual for more information: https://wind.nrel.gov/nwtc/docs/AeroDyn_Manual.pdf.

Best regards,
Jason Jonkman, Ph.D.
Senior Engineer | National Wind Technology Center (NWTC)

National Renewable Energy Laboratory (NREL)
15013 Denver West Parkway | Golden, CO 80401
+1 (303) 384 – 7026 | Fax: +1 (303) 384 – 6901
nwtc.nrel.gov

Adrian.Gambier
Posts: 9
Joined: Wed Dec 09, 2015 8:50 am
Organization: Fraunhofer IWES
Location: Germany

Re: FAST v8.12 and S-Function with "RotCp" in OutList

Postby Adrian.Gambier » Fri Dec 11, 2015 8:00 am

Hi Bonnie
Hi Jason

thank you very much for the quick reply.

I changed now all old names by the new ones in the OutList, including
"Wind1VelX", "RtAeroCp", "RtAeroCq", "RtAeroCt" and "RtTSR"
with NWindVel =1, WindVxiList(1)=0, WindVyiList(1)=0, and WindVziList(1)=90
and CompAero=2.

However, I am still receiving the same answer, i.e.
"XX is not an available output channel", for all mentioned outputs.

Do you have any suggestion?
Best regards
Adrian

Bonnie.Jonkman
Posts: 566
Joined: Thu Nov 10, 2005 10:51 am
Organization: Envision Energy USA
Location: Colorado
Location: Boulder, CO
Contact:

Re: FAST v8.12 and S-Function with "RotCp" in OutList

Postby Bonnie.Jonkman » Fri Dec 11, 2015 9:33 am

Are you specifying them in the appropriate input files? Wind1VelX must be specified in InflowWind; "RtAero*" must be specified in the AeroDyn v15 input file.

The error message should tell you what module is complaining about invalid channel names. Then you can go into that module's input file and remove the offending channels.
Bonnie Jonkman

Envision Energy USA, 2016-
National Renewable Energy Laboratory, 2003-2016


Return to “Computer-Aided Engineering Software Tools”

Who is online

Users browsing this forum: No registered users and 1 guest